Terms of sale
These terms apply to purchases of pattern downloads on glasscutpatterns.com, operated by WEABLE SAS. WEABLE SAS, 27 avenue Jean Medecin, 06000 Nice, France. RCS Nice 891 213 936. VAT FR71891213936. Contact: [email protected]. Hosting: Hetzner Online GmbH, Industriestr. 25, 91710 Gunzenhausen, Germany.
Products and pricing
Individual patterns are $9. The Beginner Pack is $24. The Complete Collection is $39. Prices are shown in USD at checkout.
Delivery
Patterns are delivered as a digital download, generated for the panel size and technique chosen at checkout, with a link provided immediately after payment and on the files page.
Right of withdrawal for digital content
Because delivery is immediate and the file is generated specifically for the size you chose, the download link becoming available is treated as the start of performance for this digital content; refund requests are handled case by case by contacting support before downloading.
Usage rights
A purchased pattern may be used to cut personal or small-batch commercial glass projects. Reselling, redistributing, or republishing the pattern files themselves is not permitted.
Delivery
All products are digital downloads. Once payment is confirmed the ZIP appears immediately on the files page, generated for the panel width and technique chosen at checkout. There is no shipping step and no wait on an email.
Right of withdrawal
For digital content supplied without a physical medium, the right of withdrawal does not apply once performance has begun with the customer's prior express consent. Downloading the pattern constitutes performance. The free pattern and the live sizing tool allow the format, the checks and the content of a pattern set to be evaluated before any payment.
Rebuilds
A pattern can be regenerated at a different size within its declared range, or for the other cutting technique, at no extra charge, on request from the contact page quoting the email address used at checkout. There is no time limit on that request and no expiry on downloads.
Licence
A purchased pattern may be used to build panels, including panels the buyer sells. Redistribution or resale of the pattern files themselves is not permitted.
Claims and applicable law
Claims may be sent to [email protected]. These terms are governed by French law. Failing an amicable settlement, disputes fall to the competent courts.
Practical checkout and download procedure
Before checkout, measure the intended panel opening with a rigid tape measure, not a cloth tape. Record the clear opening width and height in millimetres or inches, then measure a second time from the opposite side. For rectangular openings, a difference of 2 mm to 3 mm between two measurements is common on older frames and should be resolved before generating the file.
Use an email address that you can access from the same device used for the download. Keep the checkout email, the browser receipt screen, and the saved ZIP in one project folder. A clear folder name such as kitchen-transom-740x310 avoids confusion later when several panels are being cut for the same building.
After payment confirmation, open the files page and download the ZIP before starting other browser work. A typical pattern ZIP is small enough to download on a normal home connection in less than 1 minute, but the exact time depends on the connection and the generated file. If the browser asks where to save the file, choose a local folder rather than a cloud-only location, then confirm that the ZIP file size is greater than 0 bytes.
Unzip the file before printing or sending it to a print shop. Do not print directly from the compressed ZIP preview, because some systems show a temporary copy and may hide the real page size controls. If you need help finding account or download answers, use the FAQ before regenerating or reprinting.
Equipment, dimensions, and checks before cutting
The non-glass equipment needed for a controlled workflow is simple: a computer or tablet for downloading, an unzip tool, a PDF viewer or other suitable file viewer for the supplied pattern files, a printer or print shop, a ruler at least 300 mm long, a cutting surface, masking tape, and a pencil for marking job notes. For shop use, add a project envelope or flat folder so printed sheets stay in order.
Print scale is the main technical check. Any printed page that contains a reference scale or border should be measured with a ruler before glass is cut. A 100 mm reference must measure 100 mm on paper. If it measures 97 mm or 103 mm, the print is off by 3 percent, which is large enough to move lead lines, foil allowances, and edge fit on a finished panel.
| Check | Target figure | Action if outside target |
|---|---|---|
| Print scale | 100 mm prints as 100 mm, or 4 in prints as 4 in | Reprint at 100 percent or actual size |
| Frame measurement repeatability | Within 2 mm, about 1/16 in | Measure again and use the smaller clear opening when fit is tight |
| Paper sheet alignment | Lines meet within 1 mm at taped joins | Retape sheets before tracing or cutting |
| Glass edge clearance | Project dependent, commonly checked before final cut | Confirm against the construction method and frame condition |
For tiled prints, trim only the margins needed for joining and tape from the back first. Check the full width and height after assembly. On a 900 mm panel, a 1 percent print error becomes 9 mm, which is visible and may prevent the panel from fitting its frame.
Frequent mistakes and recovery steps
- The ZIP was downloaded but cannot be found. Check the browser downloads list first, then the operating system Downloads folder. Search by the purchase date if the file name is not remembered.
- The file opens in a browser and prints too small. Save the file locally, open it from the folder, and choose actual size or 100 percent in the print dialog. Disable fit to page when exact scale is required.
- The wrong panel size was entered. Stop before cutting glass. Keep the original file for reference, note the correct width and technique, and request a rebuild with the checkout email.
- Sheets were taped slightly crooked. Do not correct by stretching or forcing the drawing. Separate the sheets, align two crossing lines or borders, then tape again. A 1 mm error at each join can add several millimetres across a large pattern.
- The print shop changed the scale. Ask for a reprint at 100 percent and give the shop one measured reference dimension to verify before all sheets are printed.
If a mistake is discovered after some glass has already been cut, separate the problem into pattern scale, assembly alignment, and glass cutting accuracy. Measure one known straight dimension on the paper first. If the paper is correct, compare the cut pieces to the corresponding templates. If both are correct but the project still does not fit, recheck the original frame dimensions and squareness.
Special cases to plan before ordering or rebuilding
For old timber or metal frames, check squareness by comparing diagonals. If one diagonal is 6 mm longer than the other on a small panel, the opening is not square. A rectangular pattern may still be used, but the installation method must account for the frame condition.
For multi-panel projects, keep a separate measurement record for each opening. Two windows that look identical can differ by 3 mm to 10 mm after repainting, settlement, or previous repairs. Label them left, centre, and right from one fixed viewing side, then use the same labels on printed patterns and glass storage.
For workshop handoff, send the ZIP or the unzipped files together with the intended finished width, technique, and any frame notes. Do not rely on a verbal dimension such as standard bathroom size. Written dimensions reduce the risk of a wrong print scale or a rebuild request based on incomplete information.
If the download device is a phone, use it only to obtain the file, then transfer the ZIP to the computer or print shop without renaming it several times. If access questions remain, check the FAQ and keep the checkout email available when contacting support.
Read next
- Complete Collection: every pattern in one download: Complete Collection bundles all seven beginner and intermediate patterns in one download, sized 12 to 24 in across every pattern, for only $39 total.
- Crescent Moon: a full moon panel for your first ground curve: Crescent Moon: a two-arc crescent in a banded night sky with diamond stars, a beginner pattern with one ground curve, sized 10 to 24 in, 25 pieces.
- Diamond Lattice: a framed lattice panel for straight-cut practice: Diamond Lattice: a double-bordered checkerboard of diagonal diamonds, straight cuts only, sized 8 to 24 in, 32 pieces, with a full glass list.
